收藏本站
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
LOGIC COMMANDS AND REGISTERS
COMMAND DESCRIPTIONS
The IC contains internal registers to control the various
operating parameters, modes, and interrupt characteristics.
These commands are sent and status is read via 8-bit SPI
commands. The IC will use the last eight bits in a SPI transfer,
so devices can be daisy-chained. The first three bits in a SPI
Table 7. Command List
word can be considered to be the Command with the trailing
five bits being the data.
The SPI logic will generate a framing error and ignore the
SPI message if the number of received bits is not eight or if it
is not a multiple of eight.
After RST, the first SPI result returned is Status Register 0.
Command
000 x xxxx
001 0 xxxx
001 1 xxxx
010x xxxx
011 0 xxxx
011 1 xxxx
100x xxxx
Name
NULL
MASK0
MASK1
Mode
CLINT0
CLINT1
DEADTIME
Description
These commands are used to read IC status. These commands do not change any internal IC status. Returns
Status Register 0-3, depending on sub command.
Sets a portion of the interrupt mask using lower four bits of command. A “1” bit enables interrupt generation
for that flag. INT remains asserted if uncleared faults are still present. Returns Status Register 0.
Sets a portion of the interrupt mask using lower four bits of command. A “1” bit enables interrupt generation
for that flag. INT remains asserted if uncleared faults are still present. Returns Status Register 0.
Enables Desat/Phase Error Mode. Enables FULLON Mode. Locks further Mode changes. Returns Status
Register 0.
Clears a portion of the fault latch corresponding to MASK0 using lower four bits of command. A 1 bit clears
the interrupt latch for that flag. INT remains asserted if other unmasked faults are still present. Returns Status
Register 0.
Clears a portion of the fault latch corresponding to MASK1 using lower four bits of command. A 1 bit clears
the interrupt latch for that flag. INT remains asserted if other unmasked faults are still present. Returns Status
Register 0.
Set deadtime with calibration technique. Returns Status Register 0.
FAULT REPORTING AND INTERRUPT
GENERATION
Different fault conditions described in the previous
chapters can generate an interrupt - INT pin output signal
asserted high. When an interrupt occurs, the source can be
read from Status Register 0, which is also the return word of
most SPI messages.
Faults are latched on occurrence, and the interrupt and
faults are only cleared by sending the corresponding CLINTx
command. A fault that still exists will continue to assert an
interrupt.
Note: If there are multiple pending interrupts, the INT line
will not toggle when one of the faults is cleared. Interrupt
processing circuitry on the host must be level sensitive to
correctly detect multiple simultaneous interrupt.
Thus, when an interrupt occurs, the host can query the IC
indicating any faults not cleared since the CLINTx command
was last written (rising edge of CS) and the beginning of the
current SPI command (falling edge of CS). The NULL
command causes no changes to the state of any of the fault
or mask bits.
The logic clearing the fault latches occurs only when:
1. A valid command had been received(i.e. no framing
error);
2. A state change did not occur during the SPI message
(if the bit is being returned as a 0 and a fault change
occurs during the middle of the SPI message, the latch
will remain set). The latch is cleared on the trailing
(rising) edge of the CS pulse. Note, to prevent missing
any faults the CLINTx command should not generally
clear any faults without being observed; i.e. it should
only clear faults returned in the prior NULL response.
by sending a NULL command; the return word contains flags
33927
Analog Integrated Circuit Device Data
Freescale Semiconductor
29
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
MCZ33937EKR2 IC PRE-DRIVER 3PHASE 54-SOIC
MDN2BL3GRAS MOTOR BRUSHED DC 2V 2753RPM
MDN3BL3CSAS MOTOR BRUSHED DC 2V 1458RPM
MIC2287-34YML TR IC LED DRIVER WHITE BCKLGT 8-MLF
MIC2289C-34YD6 TR IC LED DRIVR WHITE BCKLGT TSOT-6
MIC2291YD5 TR IC LED DRIVER PHOTO FLASH TSOT-5
MIC2293-15YML TR IC LED DRIVER WHITE BCKLGT 8-MLF
MIC2293C-34YML TR IC LED DRIVER WHITE BCKLGT 8-MLF
相关代理商/技术参数
MCZ33927EK/R2 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Three-Phase Field Effect Transistor Pre-Driver
MCZ33927EKR2 功能描述:功率驱动器IC THREE PHASE PRE- DRIVER RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube
MCZ33927R2 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Three-Phase Field Effect Transistor Pre-Driver
MCZ33937AEK 功能描述:马达/运动/点火控制器和驱动器 3 Phase Pre-Driver RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
MCZ33937AEK/R2 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Three Phase Field Effect Transistor Pre-driver
MCZ33937AEKR2 功能描述:马达/运动/点火控制器和驱动器 3 Phase Pre-Driver RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
MCZ33937EK 功能描述:功率驱动器IC THREE PHASE PRE DRIVER RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube
MCZ33937EK/R2 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Three Phase Field Effect Transistor Pre-driver